XL Joinery

Internal Laminate Umber Grey Ravenna Door (Pre-Finished)

As low as £163.68 £136.40

In stock
Only %1 left
SKU
LUMBRAV
  • Fast Delivery
  • Secure Payments
  • Price Match Promise
More Information
SKU LUMBRAV
Door Style Ravenna Internal Umber Grey Laminate Door
Specialist Door Type Internal Door
Finish Pre-Finished
Colour Umber Grey
Door Design Full thickness with deep u-grooved design and horizontal and vertical grain
Lipping Size Note: trimmed edges and hardware cut-outs require finishing
Construction Semi solid core
FSC Yes
Brand XL Joinery

XL Joinery Ltd

How To Install And Care For XL Joinery Internal Doors

Installation

When trimming a door to fit, 6mm can be removed from each edge of the door to a maximum reduction of 12mm in both the height and width. Any reduction must be removed evenly from each edge of the door, e.g. to trim your door by 8mm in width, remove 4mm off each side. (Excludes Fire Doors, Bi-Folds and rebated door pairs).

Three hinges should be used to hang doors, particularly on glazed, heavyweight and fire doors or where large differences in temperature or humidity may occur, such as bathrooms.

Latches and locks should not be fitted adjacent to door mid-rails where the joint may be compromised.

All hardware screw holes should be pre-drilled to prevent splitting of the timber.

Paint ‘N’ Peel (glass protection film) should not be removed until painting or staining has been completed. Some glass styles are smooth on one side and obscure on the other: Please check that the obscure glazed faces of multiple doors are orientated in the same direction, e.g. if installing 2 glazed doors side by side.

Fire doors have individual fitting guidelines and the installer must refer to the Global Assessment Report referenced on the front of the fire door label.

Bi-Fold doors are supplied with a track and folding hardware and should not be trimmed. Rebated Door Pairs are supplied with separate instructions for fitting / trimming.

Finishing

Bare timber doors will require a light sanding prior to finishing.

Take care when finishing glazed doors to ensure that the finish does not go on the glass. Secondary protection such as masking tape may be necessary, including on Paint ‘N’ Peel protected doors.

All timber surfaces should be fully finished. When applying the finish pay particular attention to sealing the timber end grain on the tops and bottoms of the doors: Ensure that all lock, latch and hinge cut-outs are also fully treated. Refer to the finish manufacturer’s instructions for number of coats to be applied.

Failure to treat all the timber surfaces may lead to excessive changes in moisture content which will cause the timber to shrink or swell, possibly causing splits and distortion.

White Moulded and White Primed doors require a top coat after fitting. They are only suitable for painting. All edges and cut outs should be treated before final fitting.

Factory finished doors will require any bare timber areas caused by trimming and hardware fitting, to be adequately treated before final fitting.

Pre-Finishing Summary

DO

  • Use a good quality paint, stain or varnish
  • Apply to all faces and edges
  • Apply the same number of coats equally to the face, edges, lock, latch and hinge cut-outs
  • Apply at least 1 coat of finish as soon as possible after unpacking the door
  • Check that the finish manufacturers’ product is suitable for veneered / engineered doors.

DO NOT

  • Use thin penetrating seals, oils, wax, dyes or hard, brittle finishes
  • Use thinned / mixed paints or stains
  • Mix incompatible products, e.g. paint on one door face and stain on the opposite face.

Guarantee

XL Joinery pride themselves on supplying quality products, and are pleased to offer the following guarantees on their products:

  • 30 Year Manufacturing Defect Warranty on all oak Statement Palermo and oak Statement Suffolk doors
  • 25 Year Manufacturing Defect Warranty on all oak Original Palermo and oak Original Suffolk doors.
  • 10 Year Manufacturing Defect Warranty on all composite door sets and Hardwood, oak, walnut, grey, white primed and pine doors.
  • 1 Year Manufacturer’s Defect Warranty on gates, frames / linings, white moulded Doors and Crysta-Glas.
  • Additional warranties on external Tricoya and Accoya doors. As stated on the product labels.
  • 5 Year Manufacturer’s Defect Warranty on handle packs.

All Guarantees are subject to the door set being prepared, installed and treated in accordance with XL Joinery recommendations for installation, subject to their terms and condition, full details and be found on XL Joinery’s website.

The delivery charges quoted below and in your shopping basket are for deliveries to mainland England and Wales. We will provide a price on application for delivery to Scotland and all UK Islands. We have a right to change delivery costs at short notice.

All costs of delivery include VAT at the national standard rate.

Delivery charges are per brand - if you purchase products from different brands, you will incur separate delivery charges for each brand.

Doors
1 door: £48.00
each door thereafter: £6.00 (capped at £72 per delivery excluding surcharges)

Handles
Free if purchased with doors of the same brand
£48 if purchased on their own

Folding door systems
Free if purchased with doors of the same brand
£48 if purchased on their own

Skirting, architrave and door linings
Free if purchased with doors of the same brand
£48 if purchased on their own.  Each product thereafter: £6.00 (capped at £72 per delivery excluding surcharges)

Deliveries can take up to 10 working days, depending on postcode.

Deliveries within the London Congestion Charging Zone will incur an £18 surcharge (included in the shopping basket).

Delivery to Scotland and UK island postcodes will incur surcharges - please contact us for a quote.

Unfortunately, we cannot deliver to GY, IM, JE, TR21-25, PO30 - 40 and ROI, but can drop off at a port of your choice.

We offer free delivery for all goods collected from the warehouse.

Click here for more Delivery & Returns information.